Linux version 2.6.7-gentoo-r11 (root@caius) (gcc version 3.3.3 20040412 (Gentoo Linux 3.3.3-r6, ssp-3.3.2-2, pie-8.7.6)) #12 Sun Aug 1 15:16:52 Local time zone must be set--see zic manu BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001bf70000 (usable) BIOS-e820: 000000001bf70000 - 000000001bf7c000 (ACPI data) BIOS-e820: 000000001bf7c000 - 000000001bf80000 (ACPI NVS) BIOS-e820: 000000001bf80000 - 000000001c000000 (reserved) BIOS-e820: 000000002bf80000 - 000000002c000000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 447MB LOWMEM available. On node 0 totalpages: 114544 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 110448 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI present. Sony Vaio laptop detected. ACPI: RSDP (v000 PTLTD ) @ 0x000f6fd0 ACPI: RSDT (v001 SONY K7 0x06040000 LTP 0x00000000) @ 0x1bf773fe ACPI: FADT (v001 SONY K7 0x06040000 PTL 0x000f4240) @ 0x1bf7bf64 ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x1bf7bfd8 ACPI: DSDT (v001 SONY K7 0x06040000 MSFT 0x0100000e) @ 0x00000000 Built 1 zonelists Kernel command line: root=/dev/hda3 Initializing CPU#0 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 2790.686 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Memory: 449500k/458176k available (2848k kernel code, 7908k reserved, 1008k data, 164k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 5505.02 BogoMIPS Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 128K CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU: Intel(R) Celeron(R) CPU 2.80GHz stepping 09 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfd8a0, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: IRQ9 SCI: Edge set to Level Trigger. ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 10 *11) ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 10 *11) ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 *10 11) ACPI: PCI Interrupt Link [LNK5] (IRQs 10) *11 ACPI: PCI Interrupt Link [LNK6] (IRQs 3 4 5 7 10 *11) ACPI: PCI Interrupt Link [LNK7] (IRQs 3 4 5 7 10 *11) ACPI: PCI Interrupt Link [LNK8] (IRQs 3 4 5 7 10 11) *0, disabled. ACPI: Embedded Controller [EC0] (gpe 24) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PPB_._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub ACPI: PCI Interrupt Link [LNK6] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNK7] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 10 ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 10 ACPI: No IRQ known for interrupt pin A of device 0000:00:0f.0 ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 10 PCI: Using ACPI for IRQ routing radeonfb_pci_register BEGIN radeonfb: probed SDR SGRAM 65536k videoram radeonfb: mapped 16384k videoram radeonfb: Invalid ROM signature 0 should be 0xaa55 radeonfb: Retreived PLL infos from BIOS radeonfb: Reference=14.32 MHz (RefDiv=31) Memory=183.00 Mhz, System=133.00 MHz 1 chips in connector info - chip 1 has 2 connectors * connector 0 of type 2 (CRT) : 2300 * connector 1 of type 4 (DVI-D) : 4411 Starting monitor auto detection... radeonfb: I2C (port 1) ... not found radeonfb: I2C (port 2) ... not found radeonfb: I2C (port 3) ... not found radeonfb: I2C (port 4) ... not found radeonfb: I2C (port 2) ... not found radeonfb: I2C (port 4) ... not found Non-DDC laptop panel detected radeonfb: I2C (port 3) ... not found radeonfb: I2C (port 4) ... not found radeonfb: Monitor 1 type LCD found radeonfb: Monitor 2 type no found radeonfb: panel ID string: Sharp LQ150X1LH82 XGA radeonfb: detected LVDS panel size from BIOS: 1024x768 BIOS provided panel power delay: 400 radeondb: BIOS provided dividers will be used ref_divider = 5 post_divider = 2 fbk_divider = 5b Scanning BIOS table ... 320 x 350 320 x 400 320 x 400 320 x 480 400 x 600 512 x 384 640 x 350 640 x 400 640 x 475 640 x 480 720 x 480 720 x 576 800 x 600 848 x 480 1024 x 768 Found panel in BIOS table: hblank: 320 hOver_plus: 16 hSync_width: 136 vblank: 38 vOver_plus: 2 vSync_width: 6 clock: 6500 Setting up default mode based on panel info radeonfb: Power Management enabled for Mobility chipsets radeonfb: ATI Radeon C7 SDR SGRAM 64 MB radeonfb_pci_register END tridentfb: Trident framebuffer 0.7.8-NEWAPI initializing vesafb: probe of vesafb0 failed with error -6 Simple Boot Flag at 0x35 set to 0x1 Machine check exception polling timer started. devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). udf: registering filesystem Activating ISA DMA hang workarounds. ACPI: AC Adapter [ACAD] (on-line) ACPI: Battery Slot [BAT1] (battery present) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Processor [CPU0] (supports C1 C2, 8 throttling states) ACPI: Thermal Zone [TZ01] (49 C) mice: PS/2 mouse device common for all mice serio: i8042 AUX port at 0x60,0x64 irq 12 alps.c: E6 report: 00 00 64 alps.c: E7 report: 73 02 0a alps.c: E6 report: 00 00 64 alps.c: E7 report: 73 02 0a alps.c: Status: 15 01 0a ALPS Touchpad (Glidepoint) detected Disabling hardware tapping alps.c: Status: 11 01 0a input: AlpsPS/2 ALPS TouchPad on isa0060/serio1 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 hStart = 1040, hEnd = 1176, hTotal = 1344 vStart = 770, vEnd = 776, vTotal = 806 h_total_disp = 0x7f00a7 hsync_strt_wid = 0x11040a v_total_disp = 0x2ff0325 vsync_strt_wid = 0x60301 pixclock = 15384 freq = 6500 lvds_gen_cntl: 003dffa1 Console: switching to colour frame buffer device 128x48 lp: driver loaded but no devices found sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 189) sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 199) sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 201) sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 189) sonypi: Sony Programmable I/O Controller Driver v1.22. sonypi: detected type2 model, verbose = 0, fnkeyinit = off, camera = off, compat = off, mask = 0xffffffff, useinput = on sonypi: enabled at irq=11, port1=0x1080, port2=0x1084 sonypi: device allocated minor is 63 Sony VAIO Jog Dial installed. Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected Ati IGP345M chipset agpgart: Maximum main memory to use for agp memory: 380M agpgart: AGP aperture is 128M @ 0xe8000000 [drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies Inc Radeon IGP 340M Serial: 8250/16550 driver $Revision: 1.3 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550 ttyS1 at I/O 0x8428 (irq = 11) is a 8250 ttyS2 at I/O 0x8440 (irq = 11) is a 8250 ttyS3 at I/O 0x8450 (irq = 11) is a 8250 ttyS4 at I/O 0x8460 (irq = 11) is a 8250 ttyS5 at I/O 0x8470 (irq = 11) is a 8250 parport0: PC-style at 0x378 (0x778) [PCSPP(,...)] parport0: irq 7 detected lp0: using parport0 (polling). Using anticipatory io scheduler Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) 8139too Fast Ethernet driver 0.9.27 eth0: RealTek RTL8139 at 0x9c00, 08:00:46:c2:ea:4a, IRQ 11 eth0: Identified 8139 chip type 'RTL-8100B/8139D' Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx hda: FUJITSU MHT2060AT, ATA DISK drive hdc: QSI CD-RW/DVD-ROM SBW242U, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 117210240 sectors (60011 MB) w/2048KiB Cache, CHS=65535/16/63 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 hdc: ATAPI 24X DVD-ROM CD-R/RW CD-MRW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 libata version 1.02 loaded. ohci1394: $Rev: 1223 $ Ben Collins ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[e0404000-e04047ff] Max Packet=[2048] ieee1394: raw1394: /dev/raw1394 device initialized Advanced Linux Sound Architecture Driver Version 1.0.4 (Mon May 17 14:31:44 2004 UTC). ALSA device list: No soundcards found. oprofile: using timer interrupt. NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) ip_conntrack version 2.1 (3579 buckets, 28632 max) - 296 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller NET: Registered protocol family 1 NET: Registered protocol family 17 ACPI: (supports S0 S3 S4 S5) ReiserFS: hda3: found reiserfs format "3.6" with standard journal ieee1394: Host added: ID:BUS[0-00:1023] GUID[08004603018a8809] ReiserFS: hda3: using ordered data mode ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda3: checking transaction log (hda3) ReiserFS: hda3: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 164k freed Adding 506036k swap on /dev/hda2. Priority:-1 extents:1 spurious 8259A interrupt: IRQ7. ndiswrapper version 0.8-rc2 loaded ndiswrapper adding bcmwl5.sys Linux Kernel Card Services options: [pci] [cardbus] [pm] Yenta: CardBus bridge found at 0000:00:0a.0 [104d:8158] Yenta: ISA IRQ mask 0x00a8, PCI irq 11 Socket status: 30000820 Yenta: CardBus bridge found at 0000:00:0a.1 [104d:8158] Yenta: ISA IRQ mask 0x00a8, PCI irq 10 Socket status: 30000006 PCI: Enabling device 0000:02:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:02:00.0 to 64 wlan0: ndiswrapper ethernet device 00:30:bd:f5:01:e5 using driver bcmwl5.sys ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 64 td 64 cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0800-0x08ff: clean. cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. hdc: CHECK for good STATUS eth0: link down atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. hStart = 1040, hEnd = 1176, hTotal = 1344 vStart = 770, vEnd = 776, vTotal = 806 h_total_disp = 0x7f00a7 hsync_strt_wid = 0x11040a v_total_disp = 0x2ff0325 vsync_strt_wid = 0x60301 pixclock = 15384 freq = 6500 lvds_gen_cntl: 003dffa1 atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. hStart = 1040, hEnd = 1176, hTotal = 1344 vStart = 770, vEnd = 776, vTotal = 806 h_total_disp = 0x7f00a7 hsync_strt_wid = 0x11040a v_total_disp = 0x2ff0325 vsync_strt_wid = 0x60301 pixclock = 15384 freq = 6500 lvds_gen_cntl: 003dffa1 atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. hStart = 1040, hEnd = 1176, hTotal = 1344 vStart = 770, vEnd = 776, vTotal = 806 h_total_disp = 0x7f00a7 hsync_strt_wid = 0x11040a v_total_disp = 0x2ff0325 vsync_strt_wid = 0x60301 pixclock = 15384 freq = 6500 lvds_gen_cntl: 003dffa1 atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. hStart = 1040, hEnd = 1176, hTotal = 1344 vStart = 770, vEnd = 776, vTotal = 806 h_total_disp = 0x7f00a7 hsync_strt_wid = 0x11040a v_total_disp = 0x2ff0325 vsync_strt_wid = 0x60301 pixclock = 15384 freq = 6500 lvds_gen_cntl: 003dffa1 atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. hStart = 1040, hEnd = 1176, hTotal = 1344 vStart = 770, vEnd = 776, vTotal = 806 h_total_disp = 0x7f00a7 hsync_strt_wid = 0x11040a v_total_disp = 0x2ff0325 vsync_strt_wid = 0x60301 pixclock = 15384 freq = 6500 lvds_gen_cntl: 003dffa1 atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. hStart = 1040, hEnd = 1176, hTotal = 1344 vStart = 770, vEnd = 776, vTotal = 806 h_total_disp = 0x7f00a7 hsync_strt_wid = 0x11040a v_total_disp = 0x2ff0325 vsync_strt_wid = 0x60301 pixclock = 15384 freq = 6500 lvds_gen_cntl: 003dffa1 atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly.